; ; This is supplied as a sample only. Edit with your own data and formulas as required. ; ; Edit the values and bend equations as required. ; Use 'File - Save As Text' to create an ASCII bend table file ; ;----------------------------------------------------------------------- ; ; Notations used in tables: ; ; ; ';' = remark character ; ; '*' = start of a new table ; ; '/' = special character ; U = units of tolerance; thickness; bend radius; and correction values ; m; cm; mm; micron; inch; ft;or yd ; S = sheet thickness ; R = bending radii ; A = opening angle ; T1 = Tolerance (+/-) for sheet thickness S (valid for the whole file) ; T2 = tolerance for equal min and max bending radius R ; The T2 tolerance is only utilized at the minimum and maximum ; bending radii R in the tables. For model bend radii that fall ; between two values existing in the table; the resultant ; correction value X is determined by linear interpolation ; using the appropriate x values in the table. ; T3 = tolerance for equal min and max opening angle A ; The T3 tolerance is only utilized at the minimum and maximum ; opening angles A in the tables. For model opening angles ; that fall between two values existing in the table; the ; resultant correction value X is determined by linear ; interpolation using the appropriate X values in the table. ; ;----------------------------------------------------------------------- ; ; The correction value X is applied as follows: ; ; L = A + B - x ; ; (L = unfolded length in flat pattern) ; (A = length of side A (outside measurement of bendingzone)) ; (B = length of side B (outside measurement of bendingzone)) ; ;----------------------------------------------------------------------- ; ; Angle A expressed in degrees. ; ;----------------------------------------------------------------------- ; ; ;UNITS for tolerance; thickness; bend radius and correction values ; use Autodesk Inventor standard units such as 'in' and 'mm' /U in ; ;TOLERANCES valid for the whole file ; /T1 0.000040 /T2 0.004000 /T3 0.004000 ; ; *** TABLE 1 ; ;sheet thickness /S 0.060000 ; ;bending radii /R 0.015000 0.031250 0.062500 0.093750 0.125000 0.156250 0.187500 0.218750 0.250000 ;opening angle: ------------------------ correction value x ---------- /A 0.000000 0.069986 0.036414 -0.013446 -0.057419 -0.098981 -0.139223 -0.178629 -0.217459 -0.255866 /A 1.000000 0.070431 0.037226 -0.012010 -0.055392 -0.096376 -0.136047 -0.174887 -0.213153 -0.251000 /A 5.000000 0.072209 0.040472 -0.006267 -0.047282 -0.085954 -0.123342 -0.159917 -0.195932 -0.231536 /A 10.000000 0.074432 0.044530 0.000912 -0.037146 -0.072927 -0.107460 -0.141205 -0.174405 -0.207207 /A 15.000000 0.076654 0.048588 0.008091 -0.027009 -0.059900 -0.091579 -0.122493 -0.152879 -0.182877 /A 20.000000 0.078877 0.052646 0.015270 -0.016872 -0.046872 -0.075698 -0.103781 -0.131352 -0.158548 /A 25.000000 0.081099 0.056704 0.022449 -0.006736 -0.033845 -0.059817 -0.085069 -0.109825 -0.134218 /A 30.000000 0.083322 0.060762 0.029628 0.003401 -0.020818 -0.043936 -0.066357 -0.088299 -0.109888 /A 35.000000 0.085545 0.064820 0.036807 0.013538 -0.007790 -0.028055 -0.047646 -0.066772 -0.085559 /A 40.000000 0.087767 0.068878 0.043986 0.023674 0.005237 -0.012173 -0.028934 -0.045246 -0.061229 /A 45.000000 0.089990 0.072936 0.051165 0.033811 0.018264 0.003708 -0.010222 -0.023719 -0.036900 /A 50.000000 0.092212 0.076994 0.058345 0.043947 0.031291 0.019589 0.008490 -0.002192 -0.012570 /A 55.000000 0.094435 0.081052 0.065524 0.054084 0.044319 0.035470 0.027202 0.019334 0.011760 /A 60.000000 0.096658 0.085110 0.072703 0.064221 0.057346 0.051351 0.045914 0.040861 0.036089 /A 65.000000 0.098880 0.089168 0.079882 0.074357 0.070373 0.067233 0.064626 0.062388 0.060419 /A 70.000000 0.101103 0.093225 0.087061 0.084494 0.083400 0.083114 0.083338 0.083914 0.084749 /A 75.000000 0.103325 0.097283 0.094240 0.094631 0.096428 0.098995 0.102050 0.105441 0.109078 /A 80.000000 0.105548 0.101341 0.101419 0.104767 0.109455 0.114876 0.120762 0.126967 0.133408 /A 85.000000 0.107771 0.105399 0.108598 0.114904 0.122482 0.130757 0.139474 0.148494 0.157737 /A 90.000000 0.109993 0.109457 0.115777 0.125041 0.135509 0.146639 0.158186 0.170021 0.182067 /A 95.000000 0.099666 0.098246 0.102457 0.109449 0.117579 0.126333 0.135481 0.144902 0.154522 /A 100.000000 0.090303 0.088209 0.090715 0.095837 0.102031 0.108812 0.115964 0.123372 0.130968 /A 105.000000 0.081760 0.079168 0.080309 0.083903 0.088502 0.093651 0.099148 0.104885 0.110799 /A 110.000000 0.073915 0.070977 0.071044 0.073401 0.076695 0.080503 0.084636 0.088993 0.093514 /A 115.000000 0.066667 0.063512 0.062754 0.064123 0.066362 0.069077 0.072095 0.075321 0.078699 /A 120.000000 0.059931 0.056671 0.055302 0.055896 0.057293 0.059130 0.061245 0.063553 0.066002 /A 125.000000 0.053636 0.050366 0.048569 0.048571 0.049310 0.050452 0.051850 0.053423 0.055126 /A 130.000000 0.047720 0.044522 0.042455 0.042023 0.042261 0.042866 0.043703 0.044700 0.045815 /A 135.000000 0.042129 0.039073 0.036871 0.036141 0.036014 0.036217 0.036628 0.037184 0.037846 /A 140.000000 0.036815 0.033961 0.031740 0.030828 0.030451 0.030368 0.030470 0.030700 0.031025 /A 145.000000 0.031737 0.029137 0.026995 0.025998 0.025470 0.025198 0.025089 0.025093 0.025178 /A 150.000000 0.026857 0.024553 0.022573 0.021575 0.020978 0.020601 0.020363 0.020222 0.020151 /A 155.000000 0.022141 0.020170 0.018420 0.017488 0.016891 0.016477 0.016179 0.015962 0.015803 /A 160.000000 0.017559 0.015948 0.014484 0.013674 0.013132 0.012737 0.012434 0.012196 0.012004 /A 165.000000 0.013080 0.011853 0.010718 0.010073 0.009630 0.009296 0.009032 0.008816 0.008636 /A 170.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 /A 175.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 /A 180.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 ; ; *** TABLE 2 ; ;sheet thickness /S 0.120000 ; ;bending radii /R 0.015000 0.031250 0.062500 0.093750 0.125000 0.156250 0.187500 0.218750 0.250000 ;opening angle: ------------------------ correction value x ---------- /A 0.000000 0.185468 0.136875 0.072829 0.020558 -0.026892 -0.071700 -0.114838 -0.156822 -0.197963 /A 5.000000 0.187816 0.141476 0.080945 0.031862 -0.012534 -0.054362 -0.094565 -0.133647 -0.171908 /A 10.000000 0.190164 0.146076 0.089061 0.043166 0.001824 -0.037023 -0.074291 -0.110471 -0.145854 /A 15.000000 0.192513 0.150677 0.097176 0.054470 0.016182 -0.019684 -0.054018 -0.087295 -0.119799 /A 20.000000 0.194861 0.155278 0.105292 0.065774 0.030540 -0.002345 -0.033745 -0.064120 -0.093745 /A 25.000000 0.197209 0.159879 0.113408 0.077078 0.044898 0.014994 -0.013471 -0.040944 -0.067690 /A 30.000000 0.199557 0.164479 0.121524 0.088382 0.059257 0.032333 0.006802 -0.017768 -0.041635 /A 35.000000 0.201905 0.169080 0.129640 0.099686 0.073615 0.049672 0.027075 0.005407 -0.015581 /A 40.000000 0.204253 0.173681 0.137756 0.110989 0.087973 0.067011 0.047348 0.028583 0.010474 /A 45.000000 0.206601 0.178281 0.145872 0.122293 0.102331 0.084350 0.067622 0.051758 0.036528 /A 50.000000 0.208949 0.182882 0.153988 0.133597 0.116689 0.101689 0.087895 0.074934 0.062583 /A 55.000000 0.211297 0.187483 0.162103 0.144901 0.131047 0.119027 0.108168 0.098110 0.088637 /A 60.000000 0.213645 0.192083 0.170219 0.156205 0.145405 0.136366 0.128441 0.121285 0.114692 /A 65.000000 0.215994 0.196684 0.178335 0.167509 0.159763 0.153705 0.148715 0.144461 0.140746 /A 70.000000 0.218342 0.201285 0.186451 0.178813 0.174121 0.171044 0.168988 0.167636 0.166801 /A 75.000000 0.220690 0.205885 0.194567 0.190117 0.188480 0.188383 0.189261 0.190812 0.192855 /A 80.000000 0.223038 0.210486 0.202683 0.201421 0.202838 0.205722 0.209535 0.213988 0.218910 /A 85.000000 0.225386 0.215087 0.210799 0.212725 0.217196 0.223061 0.229808 0.237163 0.244964 /A 90.000000 0.227734 0.219688 0.218914 0.224029 0.231554 0.240400 0.250081 0.260339 0.271019 /A 95.000000 0.207492 0.198978 0.196491 0.199564 0.204914 0.211512 0.218898 0.226829 0.235158 /A 100.000000 0.188987 0.180217 0.176418 0.177852 0.181429 0.186180 0.191674 0.197680 0.204061 /A 105.000000 0.171957 0.163106 0.158336 0.158473 0.160619 0.163865 0.167807 0.172230 0.177004 /A 110.000000 0.156183 0.147403 0.141954 0.141083 0.142088 0.144120 0.146802 0.149932 0.153390 /A 115.000000 0.141484 0.132905 0.127024 0.125396 0.125509 0.126576 0.128246 0.130332 0.132723 /A 120.000000 0.127707 0.119440 0.113342 0.111170 0.110604 0.110919 0.111791 0.113047 0.114585 /A 125.000000 0.114724 0.106864 0.100732 0.098199 0.097139 0.096885 0.097143 0.097752 0.098620 /A 130.000000 0.102422 0.095051 0.089044 0.086307 0.084910 0.084246 0.084046 0.084167 0.084523 /A 135.000000 0.090705 0.083893 0.078145 0.075341 0.073742 0.072803 0.072282 0.072049 0.072027 /A 140.000000 0.079487 0.073295 0.067922 0.065166 0.063481 0.062382 0.061656 0.061185 0.060902 /A 145.000000 0.068694 0.063173 0.058273 0.055663 0.053990 0.052830 0.051996 0.051386 0.050939 /A 150.000000 0.058258 0.053450 0.049106 0.046725 0.045146 0.044009 0.043149 0.042482 0.041955 /A 155.000000 0.048117 0.044059 0.040339 0.038255 0.036840 0.035792 0.034976 0.034320 0.033781 /A 160.000000 0.038216 0.034936 0.031896 0.030164 0.028968 0.028065 0.027348 0.026759 0.026264 /A 165.000000 0.028502 0.026023 0.023706 0.022370 0.021435 0.020721 0.020146 0.019668 0.019259 /A 170.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 /A 175.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 /A 180.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000